HAWE比例調壓閥技術特性，哈威比例調壓閥材質壽命
Pressure regulator can be said that the basic pressure relief valve, the working principle of the valve as follows:
High-pressure medium through a small hole into a relatively large cavity to achieve decompression,
In fact, by blocking the pressure, the diaphragm or piston on both sides of the mouth is the outlet,
主要作為執行機構的預調節閥,可達19bar
此壓差＝PA-PR,并與比例電磁鐵的電流成比例變化.
通過出口A處的壓力PA可以操縱液壓執行機構,并可實現對對變量泵,比例閥等的無級調節.
比例電磁鐵的功率需求非常低,
樣本D78817/1,D7831/1或D7835中的EV型放大器以及D7845 FF 中的PLVC型可編程總線控制器可以作為控制裝置。
P口處允許進口壓力(系統壓力)被限制在40bar,在較高壓力情況下,
為避免慣性時間后的調節不準確以及切換跳躍,需將壓力預先降低至PP＝40bar。
單閥訂貨實例;PM11-7-B0,6-G24/1
閥組訂貨實例;PMZ1A51-11/1-11/1-1-G24
One side is man-made pressure, and control the size of the stem and the diaphragm (piston) connected,
So as long as a fixed pressure, then the pressure of the outlet chamber will always be equal to this pressure,
This given pressure can be provided by a spring or air source or hydraulic source.
壓力差Pmax=19 bar
流量Qmax=2 lpm
概述
PM和PMZ型調壓閥為鋼制直動式調壓閥,由閥體,調節閥心,閥套和比例電磁鐵構成。
它能將由P口處進入的不穩定的系統壓力在閥出口A處降低為一個較低的,恒定的壓力差。
調壓閥基本可以說是減壓閥，減壓閥的工作原理如下：
高壓介質通過一個小孔充到一個相對較大的腔里實現減壓，
This differential pressure = PA-PR,
and with the proportional electromagnet current proportional change.
The pressure PA at the outlet A can be operated by the hydraulic actuator and
the stepless adjustment of the variable pump, proportional valve, etc. can be achieved.
Proportional electromagnet power requirements are very low,
HAWE比例調壓閥技術特性，哈威比例調壓閥材質壽命
